PicoScope 2104 håndholdt oscilloskop

Pico Technology
PP317
Udgået produkt
PicoScope 2104 håndholdt oscilloskop
  • Beskrivelse
  • Mere information
  • Specifikationer
  • Ergonomically designed to fit in the hand
  • Up to 50MS/s real-time sample rate
  • Up to 10MHz bandwidth
  • Digital ETS enhances repetitive signal sample rate to 1GS/s
  • Up to 8k sample buffer
  • Connected and powered by USB
  • Supplied with PicoScope, PicoLog and 32-bit programming libraries
  • Operates with Windows XP (SP2 or later), Vista, Windows 7, 8 and 10 (32- and 64-bit) 

PicoScope-2104 produceres og sælges ikke længere
Se 
PicoScope 2204A for erstatning

Håndboldt USB-oscilloskop, 50MS/s

The PicoScope 2104 USB Pen Scope has combined features integral to many high performance bench top oscilloscopes, with a small, lightweight and ergonomic package that fits perfectly in the hand. When used in conjunction with PicoScope® software, the PicoScope 2104 converts any laptop or desktop PC with USB support into a powerful oscilloscope without the need for additional probes or power supplies.

The PicoScope 2104 is a portable handheld oscilloscope that is ideally suited for use by hobbyists, students, technicians, and anyone looking for an easy-to-use, affordable, single-channel PC oscilloscope.

Power and performance in your hand
Handheld oscilloscopes from Pico have been ergonomically designed to fit perfectly in your hand. Whether you’re left-handed, right-handed, have big or small hands, PicoScope handheld scopes are lightweight and comfortable to use.

The small size of PicoScope handheld oscilloscopes makes them ideal for portable use, while still including the powerful features normally found in larger oscilloscopes. The PicoScope 2104 has a 50 megasample per second real-time sampling rate. For repetitive signals the sampling rate can be increased to 1 gigasamples per second using digital equivalent-time sampling. These high sampling rates combined with a 8,000 sample buffer memory and 10 MHz analogue bandwidth make the PicoScope 2104 suitable for a wide range of trouble-shooting tasks on both analogue and digital circuits.

Power and performance in your hand
Using your PicoScope handheld oscilloscope could not be easier: plug-and-play technology allows you to simply plug the oscilloscope into a USB port and start using it straight away. No need for power supplies, additional oscilloscope probes or complex installation procedures.

Designed for single-handed operation, the oscilloscope can be controlled using a button located on the top of the scope. Press the button to start the oscilloscope; the button will flash green to indicate the scope is running. A beam of light will illuminate the tip of the scope so you can clearly see the area being probed. Once you’ve captured your signal, press the button again. The button will glow red to indicate the scope has stopped.

To make your oscilloscope even easier to use you can activate PicoScope’s powerful autosetup function by simply holding down the button. The autosetup function will automatically set up the timebase and trigger configuration to display the signal that PicoScope finds on the scope’s input.

A complete test and measurement lab in a single instrument
PicoScope handheld USB oscilloscopes are supplied with PicoScope oscilloscope software that provides oscilloscope, spectrum analyzer and meter functions. PicoScope software makes full use of your PC’s processing capabilities allowing you to view real-time signals, zoom in on your signal, and save and print captured waveforms.

Also supplied is PicoLog data acquisition software. With PicoLog you can transform your PC into a high-speed data logger.

We realise that you may want to write your own software, or use a third-party package, so we also supply a 32-bit driver with fully documented programming interface, and example programs in C, Visual Basic, Delphi, LabVIEW and VEE.

PicoScope 2104 and 2105 handheld oscilloscopes come complete with an accessory kit that includes a ground clip, hooked tip and insulating tip shrouds. In the unlikely event that you damage the PicoScope’s tip, it can simply be unscrewed and replaced.

All you need in a handheld oscilloscope
Equally at home both in the lab or the field, a Pico handheld oscilloscope eliminates the need for power supplies and oscilloscope probes. With oscilloscope, spectrum analyzer, meter and data logger functions, all in an incredibly easy-to-use package, a Pico handheld oscilloscope gives you the performance, features and quality you would expect from a Pico oscilloscope, all at an affordable price.

Oscilloscope – vertical
Model PicoScope 2104 PicoScope 2105
Input channels 1
Input type Built-in oscilloscope probe
Bandwidth 10 MHz 25 MHz
Rise time (calculated) 35 ns 14 ns
Vertical resolution 8 bits
Enhanced vertical resolution 12 bits
Input sensitivity 20 mV/div to 4 V/div (10 vertical divisions)
Input ranges (full scale) ±100 mV  to ±20 V  in 8 ranges
Input coupling Software selectable AC/DC
Input characteristics 1 MΩ in parallel with 20 pF
DC accuracy ±3%
Linearity < 1 LSB at 25 °C
Overvoltage protection ±50 V  (DC + AC peak)
Oscilloscope — horizontal
Maximum sampling rate (real-time) 50 MS/s 100 MS/s
Maximum sampling rate (repetitive signals, ETS mode) 1 GS/s 2 GS/s
Maximum sampling rate (continuous streaming mode) 1 kS/s in PicoScope 6
Record length limited to 64 kS in PicoScope, unlimited when using the SDK
Timebase ranges 200 ns/div to 5000 s/div
(10 ns/div to 5000 s/div with ETS)
100 ns/div to 5000 s/div
(5 ns/div to 5000 s/div with ETS)
Buffer memory# 8 kS 24 kS
Maximum buffer segments 10,000
Maximum waveforms per second 180 wfm/s (PC-dependent)

# Shared between active channels

Triggering
Source Main input
Trigger modes None, auto, repeat, single
Digital triggers Rising edge, falling edge
Maximum pre–trigger capture Up to 100% of capture size
Maximum post–trigger delay Up to 4 billion samples (selectable in 1 sample steps)
Trigger level Adjustable over whole of selected voltage range
Trigger sensitivity Digital triggering provides 1 LSB accuracy up to full bandwidth of scope
Spectrum analyzer
Frequency range DC to maximum bandwidth of scope
Display modes Magnitude, peak hold, average
Windowing functions Rectangular, Gaussian, triangular, Blackman, Blackman–Harris, Hamming, Hann, flat-top
Number of FFT points Selectable from 128 to 4096 in powers of 2 Selectable from 128 to 16384 in powers of 2
X axis Linear or log 10
Y axis Logarithmic (dbV, dBu, dBm, arbitrary) or linear (volts)
Math channels
General functions −x, x+y, x−y, x*y, x/y, x^y, sqrt, exp, ln, log, abs, norm, sign, sin, cos, tan, arcsin, arccos, arctan, sinh, cosh, tanh, derivative, integral, delay
Filter functions Low pass, high pass, band stop, band pass
Graphing functions Frequency, duty cycle
Multi-waveform functions Min, max, average, peak
Operands Input channel, reference waveforms, time, constants, pi
Automatic measurements
Oscilloscope mode AC RMS, true RMS, cycle time, DC average, duty cycle, falling rate, fall time, frequency, high pulse width, low pulse width, maximum, minimum, peak to peak, rise time, rising rate
Spectrum mode Frequency at peak, amplitude at peak, average amplitude at peak, total power, THD %, THD dB, THD+N, SFDR, SINAD, SNR, IMD
Statistics Minimum, maximum, average, standard deviation
Mask limit testing
Mask generation Auto generate from captured waveform, manual drawing, manual coordinate entry
Actions Highlight on screen, select in buffer overview, activate alarm
Statistics Pass/fail, failure count, total count
Alarms
Initiating events Capture, buffer full, mask fail
Alarm actions Beep, play sound, stop/restart capture, run executable, save current buffer/all buffers
Display
Interpolation Linear or sin(x)/x
Persistence modes Digital color, analog intensity, fast, advanced
Data export
Output file formats BMP, CSV, GIF, JPG, MATLAB 4, PDF, PNG, PicoScope data, PicoScope settings, TXT
Output functions Copy to clipboard, print
Environmental
Temperature range (operating) 0 °C to 45 °C
Temperature range (stated accuracy) 20 °C to 30 °C
Physical properties
Dimensions
Probe
Probe and cable
Diameter

220 mm (8.6 in) long
3 m (9.8 ft) long
32 mm (1.2 in)
Software
Windows software PicoScope for Windows
PicoLog for Windows
Software development kit (SDK)
Windows 7, 8 or 10 recommended(read more)
Mac OS X software PicoScope for Mac OS X (beta)
Software development kit (SDK)
Mac OS X version 10.9 or 10.10 recommended
Linux software PicoScope for Linux (beta)
Software development kit (SDK)
See Linux Software & Drivers for details of supported distributions
Languages Chinese (simplified), Chinese (traditional), Czech, Danish, Dutch, English, Finnish, French, German, Greek, Hungarian, Italian, Japanese, Korean, Norwegian, Polish, Portuguese, Romanian, Russian, Spanish, Swedish, Turkish
General
Additional items supplied Quick start guide, software CD-ROM, accessories kit (ground clip, spring hook, BNC adaptor, insulating cap, IC probing cap, replacement probe tip)
PC connectivity USB 2.0 port (compatible with USB 1.1 and USB 3.0; USB 1.1 not recommended)
Power requirements Powered from USB port
Compliance European EMC and LVD standards
FCC Rules Part 15 Class A